/*- * Copyright (c) 1983, 1992, 1993 * The Regents of the University of California. All rights reserved. * * Copyright (C) 2007-2016 Free Software Foundation, Inc. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 4. Neither the name of the University nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ #if !defined(lint) && !defined(KERNEL) && defined(LIBC_SCCS) static char sccsid[] = "@(#)mcount.c 8.1 (Berkeley) 6/4/93"; #endif #if 0 #include #include #endif #include /* This file provides the machine-dependent definitions of the _MCOUNT_DECL and MCOUNT macros. */ #include #include /* * mcount is called on entry to each function compiled with the profiling * switch set. _mcount(), which is declared in a machine-dependent way * with _MCOUNT_DECL, does the actual work and is either inlined into a * C routine or called by an assembly stub. In any case, this magic is * taken care of by the MCOUNT definition in . * * _mcount updates data structures that represent traversals of the * program's call graph edges. frompc and selfpc are the return * address and function address that represents the given call graph edge. * * Note: the original BSD code used the same variable (frompcindex) for * both frompcindex and frompc. Any reasonable, modern compiler will * perform this optimization. */ _MCOUNT_DECL(count_ptr, selfpc) /* _mcount; may be static, inline, etc */ { register ARCINDEX *frompcindex; register struct tostruct *top, *prevtop; register struct gmonparam *p; register ARCINDEX toindex; /* Check for nested function trampoline. */ if (selfpc & 2) selfpc = *(u_long *) (selfpc + 10); p = &_gmonparam; /* * check that we are profiling * and that we aren't recursively invoked. */ #if 0 if (catomic_compare_and_exchange_bool_acq (&p->state, GMON_PROF_BUSY, GMON_PROF_ON)) return; #elif defined (__ARC700__) /* ??? This could temporarily lose the ERROR / OFF condition in a race, but doing an actual compare_and_exchange would be too costly. It would be better if we had a semaphore independent of the 'sticky' state, but then we could run into ABI compatibility problems with the size of struct gmonparam. */ { u_long old_state; __asm ("ex %0,%1": "=r" (old_state), "+m" (p->state) : "0" (GMON_PROF_BUSY)); if (old_state != GMON_PROF_ON) { switch (old_state) { case GMON_PROF_OFF: __asm ("ex %0,%1": "+r" (old_state), "+m" (p->state)); if (old_state == GMON_PROF_BUSY /* Switching off while we say we are busy while profiling was actually already switched off is all right. */ || old_state == GMON_PROF_OFF) break; /* It is not clear if we should allow switching on profiling at this point, and how to handle further races. For now, record an error in this case. */ /* Fall through. */ default: /* We expect here only GMON_PROF_ERROR. */ p->state = GMON_PROF_ERROR; break; case GMON_PROF_BUSY: break; } return; } } #else /* ??? No semaphore primitives available. */ if (p->state != GMON_PROF_ON) return; p->state = GMON_PROF_BUSY; #endif frompcindex = count_ptr; toindex = *frompcindex; if (toindex == 0) { /* * first time traversing this arc */ toindex = ++p->tos[0].link; if (toindex >= (ARCINDEX) p->tolimit) /* halt further profiling */ goto overflow; *frompcindex = toindex; top = &p->tos[toindex]; top->selfpc = selfpc; top->count = 1; top->link = 0; goto done; } top = &p->tos[toindex]; if (top->selfpc == selfpc) { /* * arc at front of chain; usual case. */ top->count++; goto done; } /* * have to go looking down chain for it. * top points to what we are looking at, * prevtop points to previous top. * we know it is not at the head of the chain. */ for (; /* goto done */; ) { if (top->link == 0) { /* * top is end of the chain and none of the chain * had top->selfpc == selfpc. * so we allocate a new tostruct * and link it to the head of the chain. */ toindex = ++p->tos[0].link; if (toindex >= (ARCINDEX) p->tolimit) goto overflow; top = &p->tos[toindex]; top->selfpc = selfpc; top->count = 1; top->link = *frompcindex; *frompcindex = toindex; goto done; } /* * otherwise, check the next arc on the chain. */ prevtop = top; top = &p->tos[top->link]; if (top->selfpc == selfpc) { /* * there it is. * increment its count * move it to the head of the chain. */ top->count++; toindex = prevtop->link; prevtop->link = top->link; top->link = *frompcindex; *frompcindex = toindex; goto done; } } done: p->state = GMON_PROF_ON; return; overflow: p->state = GMON_PROF_ERROR; return; } /* * Actual definition of mcount function. Defined in , * which is included by . */ MCOUNT